SLT® 와이어
다양한 분야에서 사용되는 와이어

펼치기
SLT® 와이어

포트웨인메탈의 SLT® 와이어는 고객 측에서의 생산 단계를 크게 줄이도록 제작되었습니다. 고객사에서 추가로 직진화 작업이 필요가 없고 기계가 멈춰있는 시간을 줄일 수 있는 기본적인 와이어가 필요하든, 고도의 연마공정을 거쳐도 변형되지 않는 직진화되어 있는 프리미엄 와이어가 필요하든 아니면 둘 사이의 어느 지점에 위치한 와이어가 필요하든 간에 SLT® 와이어는 생산 공정을 간소화하는 데 도움이 됩니다.

 

장점 이해하기

You can use the information below to compare all four or read on to learn more about each type.

Type 1

Type 1 SLT® 와이어는 제조 공정 단계를 줄이고, 셋업 시간을 단축하며, 추가 장비를 사용할 필요가 없습니다. 일반적으로 스테이플 와이어, 브레이딩 맨드렐 및 치과용 프로브에 사용되는 바로 사용 가능한 제품은 셋업 시간을 줄이고 추가 공정을 진행하기 전에 직선으로 펴야 할 필요가 없습니다. 이제, 공정을 간소화해 품질 훼손 없이 제품을 더욱 빠르게 출시할 수 있습니다.

Straightness variance 25.4 mm per 304.8 mm [1.00 in per 12.00 in] measured per ASTM F2819

포장 스펙 스풀에 감음

최소 허브 크기 와이어 직경의 220배

Type 2

Type 2 SLT® 와이어는 기계적으로 직선으로 펼 필요가 없기 때문에 공정 시간을 크게 줄입니다. 이 와이어는 감은 자국이 나지 않기 때문에 고객이 바로 사용할 수 있는 표면을 제공합니다. 2차 공정에서 캐스트 또는 나선을 위해 조정할 필요가 없기 때문에 Type 2 SLT® 와이어는 맨드렐 와이어, 니들 및 스테이플 와이어, 탐침 와이어, 포인트 코일링 및 마이크로 니들 응용 분야에 사용되고 있습니다.

Straightness variance 2.997 mm per 304.8 mm [0.118 in per 12.00 in] measured per ASTM F2819

포장 스펙 스풀에 감거나 길이에 맞게 자름

최소 허브 크기 와이어 직경의 300배

Type 3

Type 3 SLT® wire eliminates the need to straighten. In spring and hard conditions, this material allows for removal of up to 90% cross-sectional area by taper grinding without requiring heat treatment. Typical applications for Type 3 SLT® wire range from micro-needles, orthodontics and suture needles, to guide wires, endoscopes, and embolic filters.

직진성은 ASTM F2819에 설명된 테스트 방법을 사용하여 측정됩니다.

Straightness variance 0.508 mm per 304.8 mm [0.02 in per 12.00 in] measured per ASTM F2819

포장 스펙 스풀에 감거나 길이에 맞게 자름

최소 허브 크기 와이어 직경의 400배

Type 4

포트웨인메탈의 최고급 SLT® 와이어는 토크 응답이 1:1로 매우 뛰어나 신경 혈관 가이드 와이어, 조종 가능한 PTCA, 내시경 및 기타 정밀 응용 분야에서 널리 사용되고 있습니다. Type 4 SLT® 와이어는 주름지며 휘거나 돼지 꼬리처럼 말리는 문제가 없이 단면적의 95% 이상까지 가늘게 갈아낼 수 있도록 되어 있습니다. 조건에 상관없이 펴기 또는 추가적인 열 처리가 필요하지 않습니다. 뒤틀림 저항과 이처럼 뛰어난 연삭성 덕분에 이 SLT® 와이어는 일반적으로 가장 까다로운 응용 분야에서 사용됩니다.

직진성은 ASTM F2819에 설명된 테스트 방법을 사용하여 측정됩니다.

Straightness variance 0.254 mm per 304.8 mm [0.01 in per 12.00 in] measured per ASTM F2819

포장 스펙 길이 단위로 자르는 것만 가능

최소 허브 크기 해당 없음

 

 

설계 사양

Use the chart below to discover material condition, surface finish, and diameter possibilities for each type of SLT® wire. The sizes and conditions below reflect SLT® wire made with 304V.

SLT® 와이어 조건 표면 마감 크기 범위
mm 인치
Type 1 반경질
3/4 경질
경질
스프링
울트라 스프링
브라이트 0.0381 - 1.3716 0.0015 - 0.0540
하이텐 0.0508 - 0.8890 0.0020 - 0.0350
Type 2 경질
스프링
울트라 스프링
브라이트 0.0508 - 1.0033 0.0020 - 0.0395
하이텐 0.0508 - 0.8890 0.0020 - 0.0350
Type 3 Hard
Spring
Double Spring
브라이트 0.0508 - 1.0033 0.0020 - 0.0395
울트라 스프링 0.0508 - 0.9398 0.0020 - 0.0370
하이텐 0.0508 - 0.8890 0.0020 - 0.0350
Type 4 스프링
울트라 스프링
브라이트 0.1981 - 0.8712 0.0078 - 0.0343
하이텐 0.1981 - 0.7620 0.0078 - 0.0300

 

합금

SLT® wire is available in the following alloys:

  • 304V
  • 316LVM
  • FWM™ 1058 alloy
  • 35N LT™ alloy
  • MP35N® alloy
  • Ti-6Al-4V ELI
  • Ti-3Al-2.5V

 

Additional processing capabilities

No matter how you need your SLT® wire, we're here to make sure you get exactly what you want. We can supply SLT® wire in cut lengths or on a spool, and provide additional processing, such as:

  • Coating to provide electrical insulation or chemical separation
  • Laser ablation for adjustable coating coverage
  • Mechanical assembly of crimps, fittings, and specialized parts

 

How SLT® wire stacks up

Fort Wayne Metals conducted an extensive comparison test of its SLT® wire against two competitors that both produce rotary straight and cut wire material. The study measured the material performance of the wire samples. To see the full results, click SLT® wire comparison study.

 

If your product need falls outside of the above parameters, please contact your Fort Wayne Metals Representative to see how we can meet your specific requirements.